• A Comparison of Carbon Dioxide Absorption Rates Between Monoethanolamine and Ammonia
• A Comparison of Sobek and Lawrence Test Methods for the Determination of Neutralisation Potential and the Influence of Sample Properties
• A Critical Review of the Biochar Sequestration Process
• A Dynamic CSTR Model for SOFC
• A Mineralogical, Structural and Surface Chemical Investigation of Muscovite in Aqueous Media
• A Novel Hazard Identification Approach to Support Intelligent Diagnosis of Process Systems
• A PDE Agglomeration Model for Bayer Precipitation
• A Practical Application to Utilise Low Grade Waste Heat from Bayer Alumina Calciners
• A Study of Detachment of Coarse Particles from Bubbles Using Novel Electro-Acoustical Technique
• Adsorption Characteristics of Cu (II) And Ni (II) on Iron Oxide and Kaolin: A Kinetic and Equilibrium Study
• Adsorption Of Anionic Dye Solution Using Chemically Modified Barley Straw
• Adsorption of O-Xylene From Gas Stream By Modified Granular Activated Carbon
• Adsorption of Polythionates and Thiosulfate on Strong Base Anion Exchange Resins
• An Aerobic Composting Process of Waste from a Palm Oil Mill
• Application and Performance of Phase Change Material into Cold Storage Applications
• Application of Chemical Engineering Methods to Integrated Production Modelling
• Application of Integrated Framework of Simulation and Heuristics for Plant-Wide Control of the Styrene Monomer Plant
• Application of Low Cost Ionic Liquids for the Separation of Glycerine from Palm Oil-Based Biodiesel
• Assessing the Potential for Industrial Chemicals Production from the Sugarcane Industry
• Binary Colloidal Crystals and Hierarchical Macroporous Materials
• Biodegradation of Photo-Degraded Polyethylene Nanocomposites
• Block Copolymers and Living Emulsion Polymerisation
• Can Nanobubbles Repel Hydrophobic Surfaces?
• Carbon footprint accounting for water utilities: the process, complexities and challenges
• Carbon Pollution Measurement and Control
• Catalysts for Water Gas Shift Processing of Coal-Derived Syngases
• Catalytic Co-Pyrolysis of Waste Tyres with Oil Palm Empty Fruit Bunches
• Catalytic Oxidation of NO Over Activated Semi-Cokes by Different Preparation Methods
• Cellulose nanofibre nonwovens
• CFD modeling of Brown Coal Liquefaction Reactor
• Chemistry of Formation of a Solid Oxide Fuel Cell Electrolyte (Yttria Stabilized Zirconia)
• Close-to-streamline numerical study on gas velocity distribution in the industrial-scale electrostatic precipitator gas inlet hood
• Combined Effects of Temperature and Air Ratio on Vapor-Phase Cracking of Nascent Tar from the Rapid Pyrolysis of Cedar Sawdust
• Combustion Synthesis of Ceramic Nanoparticles For Solid Oxide Fuel Cells
• Computational Modeling of high solid flux riser flows
• Concentration Dependent Viscosity in Milk Evaporation Process
• Concentration Effect on the Inhibition Efficiency of Low Dose Hydrate Inhibitors
• Constraints on Agglomeration in Spray Drying
• Cost Evaluation Of Different Advanced Oxidation Processes Of Wastewater: A Comparison Of Uv/Tio₂, uv, o₃, and uv/o₃
• DC Magnetron Sputtered TiO2: Further Understanding the Effect of Micro Structure on its Application as a Photocatalyst
• Development of Nano-Colloidal Diatomaceous Earth Particles into Advanced Material for Water Treatment Applications
• Doping Copper-Zinc Oxide Catalyst with Lanthanum for the Low Temperature Water-Gas Shift Reaction
• Effect of Initial hydrothermal Temperatures on the Synthesis of Zeolites from Coal Fly Ash
• Effect of Inorganic Electrolytes on the Zeta Potential of RO Membranes
• Effect of Mo Loading on the Performance of Methane Aromatization Reactions
• Effect of Salt Concentration on N-Dodecane-In-Brine Nano-Emulsions Produced By Phase Inversion Temperature Method
• Effect of Self-Aggregation on Collectorless Fine Molybdenite Flotation
• Effect of Sodium Chloride on the Formation and Stability of n-Dodecane/water Nanoemulsions by the PIT Method
• Effect of Sparger Type And Aspect Ratio on Gas Hold-Up in Bubble Columns Via Electrical Resistance Tomography
• Effect of Water Chemistry on Froth Stability and Coal Flotation
• Effective and Safe Melting Treatment Process of Asbestos Wastes
• Effects of the Concentration Dependence of Diffusivity on Sorption Kinetics of Riboflavin Removal from Decalcified Whey Solutions in Batch Chromatography Columns
• Effects of Turbulence and Mineral Density on Flotation
• Efficient Energy Transfer and Controlled Drug Release in Highly Stable Novel Nanoliposomes
• Energy Dissipation During Agglomerate Impact
• Enhancement of Pt on Reducibility aAnd Catalytic Performance For Butane Hydrogenolysis of Co Supported on Nay Prepared with Rice Husk Silica
• Environmental Assessment of Different Advanced Oxidation Processes Applied to Winery Wastewater Effluent
• Establishment of Enhanced Biological Phosphorus Removal Process by Using Seed Sludge from A Conventional Activated Sludge Process
• Esterification of Free Fatty acid in Crude Palm Oil by Continuous Microwave with Ethanol
• Evaluation of a Satistical Process Control System in a Causticisation Facility
• Evaluation of Ni-Co/Al₂o₃ Supported Catalysts For Glycerol Steam Reforming: Solid-State Kinetic Analysis
• Experimental Kinetics Studies of Seeded Batch Crystallisation of Mono-Ammonium Phosphate
• Fabrication and Characterization of Hierarchically Ordered Porous Oxide and Metal Membranes
• Fast Pyrolysis of Mallee Wood: Effects of Alkali And Alkaline Earth Metallic Species Removal on Yields And Bio-Oil Quality
• Flocculation of Yeast Suspensions By a Cationic Polymer
• Formation of Polymer Blends using Click Chemistry Aspects of Grubb's Catalysed Polymerization
• Freezing and Thawing Concentrate an Aqueous Solution
• From Rheology to Tribology: Multi-scale Dynamics of Microgels, Food and other Soft Matter Systems
• FT-IR Investigation of the Functional Group Effects on Amine Activity towards Carbon Dioxide
• H₂/CO₂ Permeation through a Silicalite-1 Composite Membrane
• Heat Transportation Container Using Phase Change Material to Recover Unused Thermal Energy
• Hydrodynamic Study of Catalyst Lift Engager
• Hydrodynamics Investigation of Bubble Column Reactors: Effect of Column Configuration
• Improving Liquid Distribution in Pharmaceutical Wet Granulation: A Case Study
• Improving the Economics of Biodiesel Production through Esterification of Free Fatty Acid with Waste Glycerol
• Influence of Hydrophobic Tail on the Adsorption Behaviour of Non-Ionic Surfactants at Air/Water Interface
• Influence of Mixing and Formulation on Agglomeration And Functionality Oo Micronised Drug Powders
• Influence of Moisture on Surface Energy Determination by Inverse Gas Chromatography
• Inter-influence of Heterogeneous and Homogeneous Radical Reactions During the Catalytic Oxidation of Ethane
• Interaction of Fine and Ultrafine Particles with Gas Bubbles
• Interfacial Chemistry Mediated Behaviour of Aqueous Chlorite Dispersions
• Investigating the Flotation Recovery of Silica by Using Hydrogen Gas
• Investigation of Chlorine Transformation During the Pyrolysis oif Nacl-Loaded Victorian Brown Coal Using XANES
• Investigation of Impeller Type And Baffle Effects on Isolated Mixing Regions in a Laminar Stirred Tank
• Investigation of the Effect of Processing Conditions on the Rheology of Sheeted Oat/Gluten Dough
• Investigation of the Structural and Interfacial Chemistry Of Pigmentary Titanium Dioxide Particles
• Investigations on sonocrystallization
• Isomerization of n-Hexane Over Pt Supported on Zeolite Y Synthesized from Rice Husk Silica
• Knowledge Representation, Extraction and Generation for Supporting a Semi-Automatic Blended Hazard Identification Method
• Leaching and Rheological Behaviour of Chlorite With Fluorite in Sulphuric Acid
• Life Cycle Energy Balance of Biodiesel Production from Canola in Western Australia
• Liquid Slugging Control for Oil and Gas Pipeline Riser Systems
• Mass Transfer of Photosynthetic Gases within a Multi-phase Microalgae Production System
• Measurement of the Fines Concentration in a Milk Powder Spray Dryer Using Optical Scintillation
• Mechanical Activation of Combustion-Synthesized LaFeO₃ as Catalyst for Diesel Soot Oxidation
• Membrane Separation for Produced Water
• Mercury Leaching in Different Thiosulfate and Cyanide Solutions and its Effects on Gold Recovery
• Mercury Speciation Under Laboratory Scale Direct Iron Smelting Conditions
• Mesoporous Supported Catalysts for NOx Removal
• Metastable Zone Width for Racemic Ibuprofen in Ethanol and Aqueous Ethanol Mixtures
• Microbial Production of Xanthan Gum in a Stirred-tank Bioreactor
• Microwave Radiation Effect on Ultra Film Formation of Polyisoprene inside Admicelle Adsorbed on Silica Surface
• Mineral Characterization Using Micro X-ray Diffraction (micro XRD), a State-of-the-Art Non-Destructive Technique
• Modelling the Leaching of Copper From Two South Australian Ores
• Multi-Objective Optimisation of Single Mixed Refrigerant Natural Gas Liquefaction
• Multinational Expansion to China: Challenges and Ppportunities
• Multiobjective Multifunctional Reactor for Steam Reforming
• Mutual Solubility Study in Supercritical Extraction of Monoolein Using Carbon Dioxide Solvent: Regular Solution Equations
• NOx Reduction by V₂O₅/Al₂O₃-SiO₂ Catalyst in the Flue Gas of Municipal Solid Waste Incinerator
• Numerical prediction of the surface temperature of polyoxymethylene with various sliding geometry
• Online Analysis of Bubbling Phenomena
• Optimising Zinc Oxide Nanostructured Thin Films as a Photocatalyst for Industrial Wastewaters
• Optimization of a Volatile Organic Component Recovery Process for Multiple Economic and Environmental Objectives
• Optimization of Epoxidation Reaction of Rice Bran Oil Using Response Surface Methodology
• Optimization of Sintering Temperature for Producing Thermoelectric device of La-doped SrTiO₃
• Oxidation of Organic Contaminants by Combined Adsorption and Oxidation on Cobalt Supported Activated Carbon
• Particle Size Measurement of Silica Nano-Particles By Interactive Force Apparatus Under the Electric Field
• Particle transport of non-Newtonian suspensions in self-formed open channel
• PCA-based Method of Identification of Dominant Variables for Partial Control
• Performance of Remote Solar Thermal Power Plants
• Pipeline Protection
• Polymorphic Control of Calcium Carbonate in the Reactive Crystallization Between Na2CO3 and Ca(OH)2
• Polymorphic Design of TiO₂ Nanoparticles by Flame Engineering: Implications to Light-Induced Processes
• Pore-Filling PDMS/PMHS Membranes for Recovery of Ethylacetate from Aqueous Solution by Pervaporation
• Prediction of Octane Number for Gasoline Blends using Artificial Neural Networks and Genetic Algorithms
• Preparation and Characterisation of Polyamide-Tio₂ Membranes
• Preparation of Ceramic Membranes Using Industrial Waste as the Main Raw Materials: Effect of Particle Size and Sintering Temperature on the Porosity
• Process Design Aspects of a Large Scale Onshore Gas Terminal
• Process Modeling and Debottlenecking Study of a Vaccine Production
• Processing Fine to Ultra-fine Particles in Narrow Inclined Channels of a Reflux Classifier
• RAM Simulation for Process Plants
• Real Time Optimization and Control of Chemical Processes
• Relationship Between Aggregate and Sediment Bed Properties
• Removal of Sodium Sulfide from Waste Water By Oxidation Process in the Presence of Nano Ferric Oxide Catalyst
• Replacement Hydrogen Sulphide Plant Project for Kwinana Nickel Refinery
• Risk Matrix Fit for Purpose
• Role of the Interface in Polymeric Devices for Structural Health Monitoring
• Safety in Design – the Aker Solutions Way
• Scale-Up of a Novel Protein Extraction Process
• SEM Evaluation Of The Structure Of Dried Oat Starch Granules
• Soda Control - A New Approach Towards Increasing Alumina Precipitation Yield
• Soil Washing and Bioremediation of Slime Dam Material
• Solid-Liquid Separations Mediated By A Binary Surfactant System
• Steam Reforming of Biomass Tar over Charcoal in a Coke-Deposition/Steam-Gasification Sequence
• Stick Slip Behaviour of Agricultural Limestone During Wall Friction Tests in an Annular Shear Cell
• Strategies for Characterisation of Fine Mineral Matter in Collie Coal
• Structural Investigation of Titanyl Sulfate Dihydrate and Intermediates Formed During Thermal Decomposition
• Study effect of Colocasia Esculenta leaf as electrolyte to hydrogen production on electrochemical reaction by using electrochemical reactor
• Study of Gas-Fines in Decreasing Gas Velocity in a Packed Bed
• Supercritical Fluid Extraction and its Applications
• Supply Chain Integration - A Different Perspective to Managing Projects
• Surface Behaviour of Gas Hydrate Kinetic Inhibitors at the Air-Liquid Interface
• Synthesis and Characterization of Amino-Functionalized MWNT /Poly (methyl methcrylate) Nanocomposite
• Synthesis of Hierarchical Porous Zeolite Y Particles with Controllable Particle Size
• Synthesis of Mo2C/Al2O3 Via Propane Carburization For Fischer-Tropsch Reaction
• Temperature Dependence of Aluminum Nitride Hydrolysis in Alkaline Solution
• Temporary Protective Coating for Stainless Steel Slab Reheating Against High-Temperature Oxidation
• The Effect of Clay in the Formulation of Non-Traditional Completion Fluid for Underbalance Perforation
• The Effect of Minor Components on the Ignition of Lean Mixtures of Methane in Air
• The Effect of Parameter Uncertainty in Determining Reaction Networks
• The Effect of Spray Drying Conditions on Yields for Bioactive Extracts
• The Effect of Starch-Plasticizer(S) Interactions on the Moisture Migration Behaviour of Plasticized Low Amylose-Starch Films
• The Impact of Environmental Parameters On Toluene Degradation Using a Laboratroy-Scale Reactor With Internal Recycle
• The Influence of Interfacial Chemistry, PEO Adsorption Behaviour And Orthokinetic Flocculation Conditions in Enhanced Dewatering of Talc Suspensions
• The Role of NO and NO₂ in Partial Oxidation of Methane
• The Role of Pulp Chemistry and Particle Interaction Forces in Aqueous Muscovite Dispersions
• The Use of Helmholtz Resonance to Measure Volume: Application to Solid, Liquid and Particulate Systems
• Thermal Decomposition of Red Gum Under Pyrolysis Conditions
• Thermal Degradation of Vitamin C during the Oven Drying Process
• Thermodynamic Modelling of High Temperature Systems
• Thermogravimetric Analysis of the Co-Pyrolysis of the Blends With Malaysian Bituminous Coal (Silantek Coal) and Waste Tyres
• Toward Production of the Micro- And Mesoporous Activated Carbon From Oil Palm Shell by Chemical Activation Process with ZnCl2, H3PO4 and KOH Under Nitrogen and Carbon Dioxide Condition
• Tracking Innovation Trends in Natural Gas Processing
• Treatment of Anaerobically Digested Palm Oil Mill Effluent (POME) using Sequencing Batch Reactor (SBR)
• Tungsten Trioxide as a Visible Light Photocatalyst for Volatile Organic Compound Removal
• Understanding the Relationship Between Water Activity and Plasticized Biopolymer Type
• Unusual Yield Stress Behavior of Kaolin Clay Slurries
• Use of Box-Behnken Design for Producing Mesoporous Carbon Coated Monolith
• Use of High Temperature Rheometry to Study the Foaming Behaviour of Coal During Pyrolysis/Carbonisation in Order to Understand the Mechanisms Responsible for Coking Pressures
• Using DNA as a Drug: Challenges and Opportunities for Process Engineers
• Vapour-Liquid Equilibria Data for a Range of New Carbon Dioxide Absorbents
• Viscosity Models for New Zealand Black Liquor at Low Solid Concentrations
• Waste Materials as Precursors For Supercapacitor Electrodes

183 abstracts